Thursday, March 31, 2011

Sump Pit Installation - Don't Let it Get You Down in the Dumps

!: Sump Pit Installation - Don't Let it Get You Down in the Dumps

Sump pump installation can seem like a hard and dirty job. But knowing how to create a good sump pit makes a difference in the overall operation of the sump pump over time. The first consideration any homeowner should make is where does the pump need to be installed? Is the pump for use in a basement, crawl space, cellar, or perhaps a roof. Installation will vary depending on the type of pump and the use it's intended for. For the sake of pit installation any references will be for a submersible pump.

The type of soil surrounding a home needs to be taken into account. Some areas of the country like the Western Hemisphere have a lot of clay in the soil. This can cause the ground to expand and may cause foundational issues. The area the pit is put in needs to be where the best soil with a sandy consistency.  This will allow water to drain much easier. Be sure to place the pit in a location that will be very accessible for future repairs and replacement.

If the pit is to be placed in a basement that has already been built, pick the lowest spot in the basement and place the pit there. Especially if there is a certain spot in the basement where water tends to pool together. If putting the pit in a basement where concrete exists a jackhammer will be needed. It's best to cut the concrete into small pieces to make it easier to haul out later.

Most pits should optimally be 1 1/2 feet in circumference and 2 feet deep. Be sure to place all downspouts in the opposite direction of the foundation to protect it. Be certain to place all drainage from the pit in such a way that it will not drain into the sewer or a septic system. It is against the law to allow pumping from the pit into any sewer system. This can cause a sewer backup.


Sump Pit Installation - Don't Let it Get You Down in the Dumps

!: Hand Water Well Pump Save

Monday, March 21, 2011

15000gph 3/4hp Sewage Effluent Submersible Sump Water Pump

!1: Now is the time 15000gph 3/4hp Sewage Effluent Submersible Sump Water Pump Order Today!


Nice Design by :F&QOver All Rating Reviews : Great Deal : Date Created :Mar 22, 2011 03:08:05
For installation in small lift stations, drainage system or raw water applicationModel: 80WQ0.55-4PAPPLICATIONS:Home Garden and farmsMobile home parks and motelsSchool and hospitalMunicipal package systemsIndustrial treatment systemsDewatering applicationPERFORMANCE:Power: 3/4HP, 115V/60Hz, 11AMP, Single Phase, 4 poleGPM@FT: 250@5ft, 210@10ft, 140@15ft, 60@20ft shutoff@23ftSPECIFICATION:Speed: 1750RPM (nominal)Solids Handling: 2"MaxCapacities: up to 266 GPM,Total heads: up to 23 ft.Discharge: 3" NPT, VerticalAmbient Temp: 104F (40C) Continuous 140F (60C) IntermittentVOLUTE: Cast Iron, ASTM A-48 Class 30.MOTOR HOUSING: Cast Iron, ASTM A-48 Class 30.SEAL PLATE: Cast Iron ASTM A-48 Class 30.IMPELLER: 2-vane open, non-clog, Cast Iron, ASTM A-48 Class 30. Balanced for smooth operation.SHAFT: Corrosion resistance stainless steel.O-RING: BUNA-N, assures positive sealing against oil leakage.HARDWARE: 300 series stainless steel.DUAL MECHANICAL SEALS: 300 S.S. metal parts, BUNA-N elastomers.UPPER SEAL: Carbon (rotary) VS Ceramic (stationary)LOWER SEAL: Silicon Carbide VS Silicon Carbide.INSULATION: Class BCABLE: Water proof 33 ft. Cord (Plug on 115V).ENTRY: Pressure grommet for sealing and strain relief.MOTOR: Squirrel Cage Induction, Single Phase, 4 Poles, Oil filled, 115V/60Hz, 3/4Hp, Permanent Split Capacitor Type, Built-in Thermal Protector, with automatic reset.Size: 14" X 12" X 20.5"OPTIONAL: Piggy back ball float switch.

!: Order Meditation Shawl !: Red Head Gun Safes Quiz


Twitter Facebook Flickr RSS



Français Deutsch Italiano Português
Español 日本語 한국의 中国简体。